Version 9.0.0000 minor corrections not warrantying an update to Version 8.
- Flow vs. DP issue since initial Version 8 release. If bias% goes negative, bias% columns run out of alignment.
Version 8.1.0008
Released: 08/13/18
Revision List 08/13/18 Version 8.1.0008
- Labeling in two-phase steam causing pressure input box to display barometric pressure
Revision List 07/20/17 Version 8.1.0007
- Corrected beta min for honed corner orifice from 0.15 to 0.10
Revision List 03/28/17 Version 8.1.0006
- Network licenses only - force database path to application path when last used file is inaccessible.
Revision List 08/16 Version 8.1.0005
- additional labels for PT6 19.5 nozzles
Revision List 07/15 Version 8.1.0004
- 12" SCHD 60 internal diameter corrected to 14.27mm (was 12.7)
Revision List 06/18/15 Version 8.1.0003
- Export to excel function: columns A-Z not recognized
Revision List 12/29/14 Version 8.1.0002
- KDsqr was not changing for wedgemeters with manually entered pipesizes
Revision List 09/25/14 Version 8.1.0001
- Datasheet printing information not applicable to fixed geometry devices Pitot tubes and annubars '//9/14/14
- DP for v-cones reverting to previous value for internal diameter '// 9/25/14 (4x)
Revision List 05/27/14 Version 8.1.0000
- Missing Pressure values on choke orifice
- New Database Manipulation Tools
Revision List 04/16/14 Version 8.0.0009
- Fixed Geometry Enter Coefficient/MAP devices
Revision List 01/21/14 Version 8.0.0008
- Two Phase Vapor through enter fluid properties had a conversion error on the viscosity input. Input was reverting to original input. Corrected.
- European computers using a comma as a decimal place holder. This causes bizarre results in multiple screens if the database is read with commas as decimal place holders. All Flow Consultant users must have their computer set up to use a period as a decimal point. All other mathematical applications designed for English speakers require this.
Revision List 12/09/13 Version 8.0.0007
- DP screen, several inputs are missing the correction that turns a comma into a period when a comma is used for a decimal point. Corrected for version 8.0.0007.
- Corrected word wrap on cautionary message printing off the side of the page.
Revision List 10/25/13 Version 8.0.0006
- Ward Smith coefficient
- Fixed overall pressure loss unit on the engineering results screen.
Revision List 9/10/13 Version 8.0.0005
- Conversion rates for Flow Units ml and ML corrected
Revision List 04/10/13 Version 8.0.0004
- Taylor Wedge meters reverting to nominal pipe size of previous calculation
Revision List 1/10/13 Version 8.0.0003
- Print correct unit when using US or SI units but have selected a mismatched dimensional unit, such as US gas with cm
- Misc licensing enhancements
- Remove the BETA tag from the product name
Revision List 6/24/12 Version 8.0.0002
- input conversion of the user defined drainhole size was based on the selection of US vs SI units, not on the users selected dimensional unit. Corrected to reflect input of either inches or mm.
Revision List 4/5/12 Version 8.0.0001
- The pipe schedule was not selected..... error when reloading a calculation. This is caused by the manual input of a pipe size. It has been hotfixed to default to sch 40. A better solution will be in a later revision
- No solution (example), discharge coefficient with restrictive orifice plates. Reverted to version 7 code pending more testing
- After loading a previously saved file the Filename box does not update at the top of the screen, it will only update when saving a file or for the first file opened in any given database, in below for example Filename will remain as default no matter what file is loaded
- Added fluid ref input box to the print screen so users can see the fluid standard. If it’s an ENTER fluid, change the reference here
- Added a design notes box to the engineering results screen. This will print but it does not save. Under review as an enhancement
- ISA nozzle 1932 was printing 1934 on datasheet
- Pressure loss not computed on the final results of the sizing screen but printing on datasheet.
- Wandering random number in the PO box of the print screen
- Box that displays cautionary messages and prompts to print them disappears when user does a preview then clicks back
- Addition of box to enter and print Manufacturer’s recommended plate thickness (leave blank to not print that line)
|